mopeds

11 Comments »

1. Our two motorcycles (available to subscribers). the Honda Rebel and Kawasaki Ninja. have more powerful 250cc engines. making them suitable for highway riding. But their manual transmissions and higher performance require more skill to handle well. They also sacrifice practicality by having no storage. Prices were $3.399 and $3.999. respectively.

   Comment by Abraham — 05/12/2010 @ 3:15 pm

2. Underbones are often sold in the the West as scooters. Underbones. based on the 1958 Honda Super Cub. have step-through architecture but feature footpegs similar to those used on conventional motorcycles. Scooters were originally intended for low-power personal transportation with engines between 50 and 250 cc. It is still very widely used for this application. However. maxi-scooters. with engines from 250 to 800 cc. have been developed for Western markets.

   Comment by Claude — 05/12/2010 @ 3:15 pm

3. My Scooter Won t Start

   To start a scooter needs three things:

   Gas
   A spark
   Cylinder compression
   If your scooter won’t start it due to one of the above not being present. Before you start troubleshooting, make sure there is gas in the tank by actually looking into it. Don’t just trust the gas gauge!

   Most scooters have four things that need to be done before they can be started with the electric starter:

   The ignition has to be turned on
   The kill switch (usually near the right grip) has to be in the “on” position
   The rear (left) brake lever has to be squeezed.
   The starter button must be pressed.
   Some scooters may have other interlocks on the front brake or the center stand. Check your owner’s manual to make sure that you are doing all you need to?? complete the electrical circuit which enables it to start.

   If the scooter doesn’t turn over when you’ve done all the required operations, there’s an electrical problem with the battery. Make sure the battery is charged. If it is, make sure the fuse hasn’t blown. If it hasn’t, check to see if you are getting voltage to the starter motor terminals. If you are, the starter motor is likely defective. Many scooters have a kick start (see your manual). If the battery is OK and the starter motor doesn’t work, try kick starting it. It’s usually not too hard. My scooter usually starts OK on the 2nd or 3rd kick.

   If the scooter does turn over but still doesn’t start you have to check for a spark and make sure gas is getting to the engine. To check for a spark, remove the spark plug from the cylinder, hold the tip of the plug against the cylinder head and crank the engine. You should see a spark across the gap. If you don’t, there’s a problem with the ignition. Could be a faulty coil or electronic ignition module which will have to be replaced, or it could just be a lose wire.

   If you do have a spark, you need to check the gas. Make sure there is gas in the tank first! If there is you need to check the fuel valve. Most scooters use a gravity fuel feed by locating the fuel tank higher than the carburetor. The fuel usually then flows through filter and then through a vacuum operated valve. The valve has three hoses connected to it. One if from the fuel tank and is for the gas going in, one is connected to the carburetor and is for the gas coming out and one goes to the engine manifold which provides a vacuum. If you disconnect the hose from the carburetor, fuel should run out when you crank the engine (be careful to catch the gas if you do this and don’t do it with a hot engine). If you don’t see gas the fuel valve may be faulty. You can try applying a vacuum to the control port of the valve and see if the fuel flows. Sucking on the line is one way to do this (but make sure it’s the vacuum line, not the gas line if you try this!).

   Comment by master — 05/12/2010 @ 3:15 pm

4. What the carburetor does is regulate the amount of fuel and air which are supplied to the engine. To go faster you need more fuel and more air and they must be in the right proportion. The fuel also has to be atomized as much as possible (i.e. be supplied in tiny droplets). The carburetor controls all these functions and generally does it quite well. Without removing and disassembling the carburetor, there are only two adjustments you can make, but these should take care of most minor problems. The first is the adjustment of the idle speed.

   Above is a picture of a typical GY6 engine carburetor and the view is that from the right side of most engine configurations on 150cc Chinese scooters. There’s a small spring loaded screw which adjusts the idle speed. It’s right next to the throttle control which is connected to the twist grip on the right handlebar. On most 150cc scooters, idle speed should be around 1500rpm when the engine is fully warmed up. Don’t make adjustments when the engine is cold. Take a 5 or 10 minute ride first. When the engine is cold the automatic choke is in operation and that can change the idle speed. If you have a tachometer, setting the speed is easy. If you don’t, you want to set the speed to a low idle. Fast enough so that the engine doesn’t stumble or stall, but slow enough that the clutch doesn’t engage and try to move the scooter forward. On most scooters from 50cc to 250cc, this will be somewhere in the 1500-2000rpm region.

   The other adjustment you can make is to the low speed fuel/air (“mixture”) ratio. This is done on most scooters using a screw adjustment on the other side of the carburetor as shown below.

   This screw changes the air to fuel ratio at low speeds. It shouldn’t need much adjustment, but the way to do it is to turn the screw very slightly (1/8th turn) and see if the idle speed goes up or down. If it goes down, turn the screw back 1/8th turn to where it started, then 1/8 turn in the other direction and see if the idle speed goes up or down. If it goes down, turn it back to where you started since you didn’t need any adjustment! If the idle speed goes up, continue turning the screw in 1/8th turn steps until the idle speed is at a maximum. If it starts to go down, turn it back to get the maximum idle speed.

   You may need to go back to the idle speed screw to lower the idle speed if it’s now too fast. So the basic procedure is to set the fuel/air mixture to give you the fastest idle, then use the idle speed adjustment to set the speed to the lowest rpm that gives you smooth running.

   If the scooter idles well and runs fine at low speed, but has problems at high speed, the problem may lie inside the carburetor with the main jet. The fuel/air ratio at higher speeds is set by the jets inside the carburetor and to get at them the carburetor has to be removed and disassembled. This can be a tricky job as the parts are small and delicate. The good news is that these carburetors are quite cheap. You can get a new one for $60-$80, so if you can’t make your scooter run smoothly and you don’t like the idea of taking the carburetor apart, you can always replace it!

   Comment by master — 05/12/2010 @ 3:15 pm

5. I entirely concur with the earlier remark, the world-wide-web is certainly with out a question developing into the main form of communication around the world and it’s due to web sites such as this that concepts are spreading so promptly.

   Comment by my homepage — 04/17/2011 @ 3:14 am

6. You are a great blogger, I will enjoy to see extra posts by you, keep produce great material.

   Comment by solar panel diagram — 04/19/2011 @ 7:18 am

7. Its like you read my mind! You seem to know so much about this, like you wrote the book in it or something. I think that you could do with a few pics to drive the message home a little bit, but instead of that, this is excellent blog. A great read. I’ll definitely be back.

   Comment by artismed.pl — 07/28/2011 @ 9:41 am

8. Sources…

   [...]check below, are some totally unrelated websites to ours, however, they are most trustworthy sources that we use[...]……

   Trackback by Stephen Molinari MLM — 08/22/2011 @ 10:30 am

9. This web site is my inhalation, really great layout and Perfect written content material.

   Comment by Vayda Rosy — 11/10/2011 @ 7:42 pm

10. Yes of course.

    Comment by naprawa nikon — 01/06/2012 @ 9:24 am

11. Jogos Online…

    [...]below you’ll find the link to some sites that we think you should visit[...]…

    Trackback by Jogos Online — 01/12/2012 @ 2:01 pm

RSS feed for comments on this post. TrackBack URL

Leave a comment